Verify the checksum once you've copied the new image to flash: This should match the md5sum value from Cisco's download site. I highly recommend staying connected to the console to watch as the router reloads. This way you'll see any errors or warnings that may occur. Also, you should see your new image in the version information. RTR reload Proceed with reload? Reload Reason: Reload Command. May 17 Initializing memory for ECC. Use the enable password command only if you boot an older image of the Cisco IOS software or if you boot older boot ROMs that do not recognize the enable secret command.
Page 47 When you configure the console line, you can also set communication parameters, specify autobaud connections, and configure terminal operating parameters for the terminal that you are using.
Page 49 For information on interface numbering, see the quick start guide that shipped with your router. This section describes how to select a network as a default route a candidate route for computing the gateway of last resort. Example: Router config end Step 7 Displays the current routing table information. Example: Router show running-config Page Saving Your Router Configuration To aid file recovery and minimize downtime in case of file corruption, we recommend that you save backup copies of the startup configuration file and the Cisco IOS software system image file on a server.
Page 62 To view this document, you must have an account on Note routers, especially on their border routers, to improve Cisco. If you do not have an account or have forgotten security your username or password, click Cancel at the login dialog box and follow the instructions that appear.
Page Before You Begin URL filtering software, thereby allowing you to prevent users from accessing specified websites on the basis of some policy. Page 67 To find additional information on the commands used in this document, use the Command Lookup Tool. You must have an account on Cisco. If you do not have an account or have forgotten your username or password, click Cancel at the login dialog box and follow the instructions that appear.
Network Diagram This document uses the network setup shown in the diagram below. Page 68! Page 69! Page 70 Tool, which allows you to view an analysis of show command output. The small branch office requires a robust and integrated voice-mail solution. Configuration Tips The gigabit port on the router does not provide inline power. Page 81 Cisco Router gw show running-config Building configuration Current configuration : bytes!
Page 82 NAT network Page 83! RTP Packets! Page 85 switchport trunk native vlan switchport mode trunk switchport voice vlan no ip address! Page 88 session protocol sipv2 session target ipv T session target ipv Page 90 IP Communication Solution for Group Applications Configuration Example Configure ephone-dn dual-line number description Ross name Ross call-forward busy call-forward noan timeout 10 ephone-dn dual-line number description Rachel name Rachel call-forward busy call-forward noan timeout 18 ephone-dn dual-line number Page 91 IP Communication Solution for Group Applications Configuration Example Configure ephone-dn dual-line number description Jerry name Jerry call-forward busy call-forward noan timeout 18 ephone-dn dual-line number description George name George call-forward busy call-forward noan timeout 18 ephone-dn dual-line number Page 92 IP Communication Solution for Group Applications Configuration Example Configure ephone-dn dual-line number call-forward busy call-forward noan timeout 18 ephone-dn dual-line number call-forward busy call-forward noan timeout 18 ephone-dn dual-line number call-forward busy call-forward noan timeout 18 ephone-dn ephone-dn BE45 type button ephone ephone ephone ephone ephone line con 0 authorization exec LOCAL stopbits 1 line aux 0 stopbits Page 95 Certain show commands are supported by the Output Interpreter Tool registered customers only , which allows you to view an analysis of show command output.
Page 96 Representative output for each of these commands is presented in the verification summaries that follow. Note Relevant display output is highlighted as appropriate. Page 97 IP Communication Solution for Group Applications Configuration Example Verify retain-timer: 15 create cnf-files version-stamp Apr 12 transfer-system full-consult auto assign 1 to 27 fxo hook-flash local directory service: enabled.
Page IP Communication Solution for Group Applications Configuration Example Verify The following is an example of output for the show voicemail usage command on Cisco Unity Express: se show voicemail usage personal mailboxes: general delivery mailboxes: orphaned mailboxes: capacity of voicemail minutes Page Description: promptmgmt Script: promptmgmt. Before issuing debug commands, see Important Information on Debug Commands.
Page A six-port chassis might create problems. Page IP addresses. Before You Begin The following are the requirements for using this configuration example. Current configuration : bytes version Page Certain show commands are supported by the Output Interpreter Tool registered customers only , which allows you to view an analysis of show command output.
In summary: show crypto engine connections active—Shows the encrypted and decrypted packets. Page The following debug commands must be running on both IPSec routers peers. Security associations must be cleared on both peers. The voice application used in this example is Hoot and Holler, which is typically used in trading floor financial institutions for communications to branch offices. The configuration scenario emphasizes implementation of the quality of service QoS and VPN capabilities; Configuration Tips Make sure that the tunnels work before you apply the crypto maps.
Page 2! Page ! Page Hoot and Holler over V3PN Configuration Example Verify dial-peer voice voip destination-pattern session protocol multicast session target ipv This defines it as a V PN implementation. Page Hoot and Holler over V3PN Configuration Example Verify Class Map match-any class-default id 0 Match any Class Map match-all video id 3 Match ip precedence 4 Class Map match-all voice id 2 Match ip dscp ef The following is an output example for the show policy-map interface virtual-access 4 output command, performed using the configuration on the Branch 1 router: Branch-1 show policy-map interface virtual-access 4 output Virtual-Access Source: Jul 29 Page Jul 29 Learn more about how the Cisco Series Integrated Services Routers can help you build a reliable network you can count on.
You can purchase Cisco products and services that are just right for you through a Cisco Certified Channel Partner. All our partners have validated credentials and will work with you to find the best products and solutions for your biggest business challenges. Find a Cisco Certified Channel Partner in your area—specify your location and interests to find the right partner for your business.
Certain Cisco products and services for SMBs are available through online partners and can be purchased using a credit card. Purchase through an online partner. Take advantage of flexible financing options, leasing, and special programs and promotions from Cisco Capital. Have a service provider host and manage a solution for you and review available implementation options. Skip to Main content Skip to search Skip to Footer.
Count on Me The flexibility, reliability, and security you need for peace of mind. Highlights Cisco Series Integrated Services Routers support: Wireless networking: Help employees be more productive and collaborate better by enabling them to work wirelessly from anywhere in the office. Voice: Enjoy advanced communications tools such as call processing, voicemail, automated attendant, and conferencing to respond to customers faster and save money on long-distance charges.
Video: Enable more cost-effective surveillance and security systems or support on-demand and live streaming media. Security: Reduce business risks associated with viruses and other security threats.
0コメント